About the product
Feather Flags from Printdesigns use high quality, lightweight glass fibre poles and are supplied with a full colour graphic, printed and sewn in-house by our own experienced team.
All flags are supplied with a carry bag as standard and with a choice of size, shape, base type and single/double sided printing.
Print Options:
Single sided feather flags are printed in full colour onto 115gsm polyester flag material. The print shows-through to the reverse of the material with approximately 90% opacity. A single sided flag is viewable from the front and back but the image is mirrored on the reverse.
Double sided feather flags are printed in full colour onto two separate sheets of 115gsm polyester flag material. The two prints are sewn back-to -back with a layer on block-out fabric in-between. Double sided flag prints can be viewed from the front and rear without the content of the design being mirrored. Due to the additional weight, double sided flags do not flutter in the wind as freely as single sided flags.
Base Options:
Feather Flags can be supplied with a choice of two different bases. Additional bases are available for purchase separately should you wish to have maximum flexibility when using your flag.
Spike Base - Suitable for insertion into soft ground such as grass.
Cross Base - Suitable for use on hard surfaces. An optional water-weight bag is available for use with cross bases. When using cross bases outdoors, we recommend that an optional 10 Litre water weight bag be used to add additional ballast for flags up to 3.5M. For larger flags used outdoors, we recommend our large water base (see accessories link below).
If you require an outdoor base suitable for more semi-permanent use, we offer hollow plastic water/sand-fillable bases (available separately). See the accesories link at the bottom of this page. Small plastic water/sand fillable bases are suitable for 2.8M or 3.5M flags whereas the larger bases are best suited for 4.5M or 5.5M flags.
Specification
Environmental
Printing:
- No Solvents (VOC's) used in printing process
General
Dimensions (HxWxD):
- 2.8m Pole - 250 x 55cm Graphic - 200 x 59cm
- 3.5m Pole - 310 x 60cm Graphic - 260 x 62cm
- 4.5m Pole - 410 x 80cm Graphic - 340 x 70cm
- 5.5m Pole - 520 x 85cm Graphic - 450 x 77cm
Graphic
Easy-change graphic
The process of changing graphics on banner stands is easier on some models than others.
Easy-change - The print can be removed and replaced in a minute or so. You can purchase additional prints and swap between them quickly and easily.
Non Easy-change - Replacing the print is more difficult and the old graphic can be damaged during the removal process. The process could take more than 5 minutes and you may need some basic tools.
When ordering replacement prints for non easy-change banner stands, we recommend you send the old display to us so we can remove and re-fit the new print to your stand for you (there is no additional charge for this service).
Should you wish to replace the graphic on a non easy-change display yourself then we can supply the print along with fitting instructions.
:
The process of changing graphics on banner stands is easier on some models than others.
Easy-change - The print can be removed and replaced in a minute or so. You can purchase additional prints and swap between them quickly and easily.
Non Easy-change - Replacing the print is more difficult and the old graphic can be damaged during the removal process. The process could take more than 5 minutes and you may need some basic tools.
When ordering replacement prints for non easy-change banner stands, we recommend you send the old display to us so we can remove and re-fit the new print to your stand for you (there is no additional charge for this service).
Should you wish to replace the graphic on a non easy-change display yourself then we can supply the print along with fitting instructions.
- Yes
Print method
Available printing methods for this product. Actual printing method depends on selected graphic material.
:
Available printing methods for this product. Actual printing method depends on selected graphic material.
- Dye-sublimation
Downloads
-
Feather Flag ANGLED Artwork Templates (1,229 Kb)
-
Feather Flag CONCAVE Artwork Templates (1,104 Kb)
-
Feather Flag CONVEX Artwork Templates (1,235 Kb)
-
Feather Flag STRAIGHT Artwork Templates (1,857 Kb)
Printed proof
If you have very precise colour matching requirements for your artwork then we recommend purchasing a reduced-scale hard copy proof prior to printing the finished article.
Best Price Promise
Found the same product advertised cheaper elsewhere? Let us know and we'll aim to beat that price. Terms & conditions apply. See details.
Free Delivery Over £60
All orders over £60, placed online and paid for via credit/debit card, qualify for a FREE 3 working day courier delivery to UK Mainland. See details.